Search results

Page title matches

• Project File:Mapping Table – Optional
  #REDIRECT [[Project File:Mapping Table - Optional]]
  51 bytes (7 words) - 18:42, 25 February 2009
• ...d specifies that subsurface drainage be performed and identifies the input file that describes the newtork connectivity and physical description. | <pre>GRID_PIPE</pre> || ''filename.gpi'' || File that contains the information needed to link the network to the groundwater
  2 KB (252 words) - 20:19, 24 June 2013
• Project File:Mapping Table – Optional
  | <pre>MAPPING_TABLE "filename.cmt"</pre> || ''filename'' || Input ASCII file that assigns grid-based parameter values based on grid index maps. | <pre>ST_MAPPING_TABLE "filename.smt"</pre> || ''filename'' || Input ASCII file that assigns link/node parameter values based on stream index maps.
  512 bytes (73 words) - 21:16, 11 July 2013
• Project File:Overland Flow – Required
  ...r of these cards if roughness values are to be read from the Mapping Table file. ...ire watershed. Mutually exclusive with '''ROUGHNESS''' and Mapping Table file assignment.
  3 KB (518 words) - 18:58, 26 April 2019
• Project File:Interception – Optional
  .../pre> || &nbsp; || Do interception using data present in the Mapping Table file. ...tial interception abstraction (mm). Mutually exclusive with Mapping Table file assignment.
  715 bytes (96 words) - 21:17, 11 July 2013
• Project File:Rainfall Input and Options – Required
  ...ot both, PRECIP_UNIF or PRECIP_FILE must be included in each GSSHA project file. ...decoration: underline">Precipitation Input</font> for a description of the file format. Mutally exclusive with '''PRECIP_UNIF'''.
  2 KB (344 words) - 21:18, 11 July 2013
• Project File:Infiltration – Optional
  ...sture are required. Parameter values may be input using the Mapping Table file or with the series of GRASS ASCII maps using the cards below. ...'GREEN_AMPT''' or '''INF_REDIST'''. Mutually exclusive with Mapping Table file assignment.
  11 KB (1,547 words) - 18:12, 20 August 2018
• Project File:Channel Routing – Optional
  | <pre>CHANNEL_INPUT "filename.cif"</pre> || ''file name'' || Input ASCII file containing channel network connectivity and cross-sectional information for | <pre>STREAM_CELL "filename.gst"</pre> || ''file name'' || Input ASCII file containing channel/grid connectivity information.
  8 KB (1,185 words) - 19:02, 26 April 2019
• Project File:Continuous Simulations – Optional
  ...ormats, and the appropriate distributed data either from the Mapping Table file or from GRASS ASCII maps. | <pre>HMET_SURFAWAYS "filename.hmt"</pre> || ''file name'' || ASCII file with hourly HMET data formatted in the form of the NOAA/NCDC Surface Airway
  16 KB (2,345 words) - 16:31, 10 July 2018
• Project File:Saturated Groundwater Flow – Optional
  | <pre>WATER_TABLE "filename.wte"</pre> || ''file name'' || &nbsp; || Specifies the simulation of the effect of the water tab | <pre>AQUIFER_BOTTOM "filename.bot"</pre> || ''file name'' || name || Name of GRASS ASCII map of bedrock elevations (m).
  6 KB (902 words) - 21:26, 11 July 2013
• Project File:Soil Erosion – Optional
  | <pre>OUTLET_SED_FLUX "filename.osf"</pre> || ''file name'' || Output file name for outlet sediment flux (cms). Output is listed in columns, first be | <pre>ADJUST_ELEV "filename.ele"</pre> || ''file name'' || &nbsp; || &nbsp; || Inclusion of card results in new overland ele
  3 KB (454 words) - 18:34, 31 August 2018
• Project File:Constituent Transport – Optional
  ...</pre> || ''file name'' || Kg or mg/Kg || get values from mapping table || File name that contains map of contaminant loadings (Kg), or soil concentration ...listed in the '''IN_HYD_LOCATION''' file and the contaminant mapping table file.
  4 KB (570 words) - 21:28, 9 January 2017
• Project File:Subsurface Drainage Network – Optional
  ...d specifies that subsurface drainage be performed and identifies the input file that describes the newtork connectivity and physical description. ...d specifies that subsurface drainage be performed and identifies the input file that describes the newtork connectivity and physical description.
  3 KB (432 words) - 18:51, 4 October 2018
• Project File:Output Files – Required
  | <pre>SUMMARY "filename.sum"</pre> || ''file name'' || Output file summarizing information on options selected, inputs read, simulation result | <pre>OUTLET_HYDRO "filename.otl"</pre> || ''file name'' || Output file containing time series discharge at the catchment outlet. (m³/s
  13 KB (2,080 words) - 20:18, 20 February 2018

Page text matches

• General Considerations:Elevation Map
  ...cell in a GRASS ASCII map file specified with the '''ELEVATION''' project file card. The elevation data are perhaps the most important inputs for GSSHA mo ...ed will be printed on the screen and also at the bottom of the run summary file.
  4 KB (643 words) - 18:27, 3 July 2008
• Surface Water Routing:Channel Routing
  ...To use this option include the '''CHANNEL_MOMENTUM''' card in your project file. This option may be helpful for simulations where channel hydrodynamics ar ...ject card. The boundary depth, m, is specified with the '''BOUND_DEPTH''' project card. When the head boundary is specified the depth at the outlet remains
  60 KB (7,451 words) - 18:55, 26 April 2019
• Surface Water Routing:Overland Flow Routing
  ...is specified by including the '''OVERLAND_STRICT_DT''' card in the project file. This option also only works with the ''ADE'' method. While use of this o ...nd provide the name of this map to GSSHA using the '''ROUGHNESS''' project file card. Table 8 provides typical values of the Manning roughness coefficient
  15 KB (2,237 words) - 14:57, 13 October 2023
• Soil Erosion:Overland Erosion Formulation
  ...1991]. These there parameters are no longer input in the cmt input table file. :[[File:effective_stream_power.jpg]] - (a1)
  13 KB (2,066 words) - 20:45, 28 March 2013
• Soil Erosion:Simulations with Soil Erosion
  ...ote]]. Soil erosion simulations are specified with the '''SOIL_EROSION''' project card. The '''SOIL_EROSION''' card is also used to select the transport equ ...etail in Section 3.10. If channel routing is not specified in the project file only overland soil erosion calculations are performed. Sediment transport
  20 KB (2,913 words) - 17:39, 15 June 2015
• Mapping Table:Mapping Table File
  ...mation, makes calibration easier, and allows easy parameter assignment for project alternatives and future scenarios. By using index maps as the patterns for ...to obtain parameters needed for process simulations from the Mapping Table file, and that detailed ASCII maps or uniform values of parameters will not be u
  3 KB (466 words) - 18:17, 20 May 2008
• Mapping Table:Index Maps
  ...e ID numbers, and will correspond to IDs from a table in the Mapping Table file. It is from the index maps that the final structure and mapping of the data An example of a watershed mask and an index map file:
  3 KB (457 words) - 18:14, 20 May 2008
• Mapping Table:Example Mapping Table File
  ...eated. Which method is used will be determined by the card in the project file, i.e. '''GREEN_AMPT''', '''INF_REDIST''', '''INF_RICHARDS'''.
  3 KB (305 words) - 20:45, 8 August 2008
• Additional Inputs:Soil Layer Input File
  ...to the IDs in the '''SOIL_LAYER_INPUT_FILE''' table. For use with RE, the file has the following two formats depending on whether the '''RICHARD_C_OPTION'
  7 KB (960 words) - 18:09, 20 May 2008
• Creating Project Files:Creating Project Files
  ...ness, infiltration and channel routing. The third example shows a project file for GSSHA running in the continuous simulation mode with fully spatially va
  639 bytes (91 words) - 18:00, 20 May 2008
• Creating Project Files:Simple Project File
  For this project file example, we use an invented watershed data set. The topography of the wate ...t begin with the pound sign are comments, which are allowed in the project file.
  4 KB (404 words) - 20:12, 21 July 2008
• Creating Project Files:Involved Project File
  ...file will be called “simple.cip”, with a the channel/grid connectivity file "simple.gst". The format of the channel input files is described in Chapte The resulting project file for this simulation appears as:
  4 KB (502 words) - 20:11, 21 July 2008
• Creating Project Files:Continuous Simulation Project File
  ...ure, and combination land-use/soil-texture maps. In this case the project file would look like. The Mapping Table file ''simple.cmt'' would supply all the needed parameters for overland flow, ET
  4 KB (450 words) - 20:29, 9 September 2008
• Building a Model:Long-term Simulations
  ...n, 2003a) and the '''SEASONAL_RS''' card should be included in the project file if simulations are to be conducted outside the summer growing season, May-S The rainfall file and hourly hydro-met data file should be constructed to cover the calibration, verification, and simulatio
  2 KB (294 words) - 17:55, 20 May 2008
• File Formats:Nutrient Files
  ...mt). These are primarily the aquifer environment file and the point source file. These file formats are for GSSHA v3.0b.
  3 KB (481 words) - 07:41, 22 July 2008
• GSSHA Download
  ...r overland hydrodynamics. See the new cards in Manual Chapter 3 - Project File, and a description in the Manual Chapter 5 - Surface Water Routing. ...able and not included in the evapotranspiration table in the mapping table file. The automated calibration method has also been modified and undergone ext
  24 KB (3,660 words) - 15:02, 20 November 2019
• Surface Water Routing:Channel Boundary Conditions
  in the project file and then one of the two following cards ...D_TS''' the "time series name" should appear in the '''TIME_SERIES_FILE''' file. The format for all time series is the same. To have the files read corre
  861 bytes (146 words) - 21:00, 24 February 2016
• Surface Water Routing:Overland Boundary Conditions
  ...f needed, create the rating curve input file 7) adding appropriate project file cards. ...curve mapping table. This table links a unique ID value to a rating curve file. This table is not in the standard table format. It does not link to an ind
  7 KB (997 words) - 18:46, 28 January 2013
• Surface Water Routing:Embankments
  ...he low spot file is only used if you want overtopping flow. If no low spot file is specified then the dikes are assumed to never overtop. Rating curves ca == Project File Cards ==
  4 KB (674 words) - 18:50, 28 January 2013
• Mapping Table:Constituent Mapping Tables
  ...nt transport mapping table. This table is a part of the grid mapping table file (.cmt) ...tituent has its own 1) short description, 2) index map, and 3) base output file name. Additionally, the concentration of each constituent in the rainfall m
  6 KB (778 words) - 21:45, 9 January 2017

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)