Search results

Page title matches

• Post-Processing:Output control
  ...ta may be defined. This time parameter determines the frequency of writing output raster maps or data sets. The time is measured in units of minutes. ...th ''Write Frequency'', and the type of map to output, with ''Type''. The output maps can be a ''WMS'' data set in binary or ASCII format, or a series of ''
  2 KB (282 words) - 18:46, 7 May 2008

Page text matches

• Overview:Modeling Process
  ...he study. The processes to be simulated are selected in the ''GSSHA'' Job Control. It is best to start with a simple model with few processes and proceed to ...aried rainfall, soil moistures, groundwater heads, and others. Time series output of discharge and depth can be produced at all nodes in the channel network
  4 KB (635 words) - 20:05, 23 June 2008
• Overview:Modeling process
  ...he study. The processes to be simulated are selected in the ''GSSHA'' Job Control. It is best to start with a simple model with few processes and proceed to ...aried rainfall, soil moistures, groundwater heads, and others. Time series output of discharge and depth can be produced at all nodes in the channel network
  4 KB (646 words) - 23:11, 9 February 2010
• Model Construction:Building a Basic GSSHA Simulation
  The global parameters of a simulation refer to the input control and other parameters not assigned on a cell-by-cell basis; e.g., the numeri ...GSSHA'' simulation are determined based on the settings in the ''GSSHA Job Control Parameters'' dialog (Figure 3). A better description of the various option
  3 KB (422 words) - 20:35, 9 February 2010
• Model Construction:Global parameters
  The global parameters of a simulation refer to the input control and other parameters not assigned on a cell-by-cell basis; e.g., the numeri ...n a GSSHA simulation are determined based on the settings in the GSSHA Job Control Parameters dialog (Figure 4). A better description of the various options
  1 KB (219 words) - 21:52, 23 July 2008
• Model Construction:Verifying the basic model
  ...10 sec). In the ''GSSHA Job Control Parameters'' dialog, select ''Output Control'', toggle on ''Surface depth'' under the ''Data Set Map Options''. Toggle ...n, or your rainfall intensity and rerun the model. Do this until there is output. The model may or may not run to completion as flow is produced.
  4 KB (650 words) - 21:44, 23 July 2008
• Post-Processing:Output control
  ...ta may be defined. This time parameter determines the frequency of writing output raster maps or data sets. The time is measured in units of minutes. ...th ''Write Frequency'', and the type of map to output, with ''Type''. The output maps can be a ''WMS'' data set in binary or ASCII format, or a series of ''
  2 KB (282 words) - 18:46, 7 May 2008
• Template:PNav14
  :: [[Post-Processing:Output control|Output control]]
  321 bytes (25 words) - 20:17, 30 April 2008
• GSSHA Primer
  ==Output control== {{Post-Processing:Output control}}
  5 KB (532 words) - 19:56, 7 October 2008
• File Formats:Project File Format
  ...GSSHA simulation. It controls what processes run, when they run, and what output is returned. The project file references many other files. These files ofte | ''none'' || N || output hydrographs are in cms (default)
  26 KB (3,971 words) - 14:55, 13 October 2023
• Surface Water Routing:Channel Routing
  ...(negative depth occurs in one or more cells), despite the more restrictive control on the Courant number, the time step is reduced and the channel routing cal ...w longer time steps and potentially reduce simulation times. The user can control the time step coefficient for the momentum formulation by specifying a real
  60 KB (7,451 words) - 18:55, 26 April 2019
• Soil Erosion:Simulations with Soil Erosion
  ...by surface runoff detachment. The following input parameters are used to control how much sediment is detached by these two methods: ...'SOIL_EROSION''' project card. The following input parameters are used to control the sediment transport equations in each of the six methods:
  20 KB (2,913 words) - 17:39, 15 June 2015
• Tutorials:1 Initial Overland Flow Model Setup
  ==Job Control Setup== In the last step, the GSSHA™ Job Control parameters were initialized using the default values, which are mostly zero
  9 KB (1,571 words) - 20:33, 3 August 2009
• Tutorials:5 Stream Flow
  ...thalwegs refined, the stream geometry defined, and the channel routing job control item set. ...e saving the model. The stream routing option must be turned on in the Job Control dialog.
  6 KB (1,083 words) - 19:39, 11 November 2008
• Tutorials:8 Infiltration
  <li>Using the control key, select both the soil_clip.dbf and IDs_for_WMS.dbf files. Select open.< ...s shapefile. Now we need to turn on the infiltration parameters in the Job Control.
  10 KB (1,791 words) - 21:42, 2 May 2009
• Tutorials:9 Long-Term Simulations
  ...MS and set up the Long-term modeling data. First we need to set up the Job control options to turn on long-term mode. <li>Select '''GSSHA™| Job Control…'''</li>
  7 KB (1,176 words) - 14:46, 20 August 2009
• GSSHA Download
  ...ure outputs when using groundwater 3/22/19. Bug fixes related to drainage output and parameter replacement for Richards Equation inputs. Bug fixes for RELA ...See the project file for the new cards related to cumulative overland flow output. The previous LINUX and Windows versions were merged to create GSSHA 7.1.
  24 KB (3,660 words) - 15:02, 20 November 2019
• Alternate Run Modes:MPI and OpenMP Parallelization
  ...re are three parallelization modes supported. When running a simulation, a control mode and a parallelization mode are both selected; the default for most run The one factor you have control over for OpenMP, if you are running in single-run mode, is the number of th
  3 KB (542 words) - 19:47, 25 July 2008
• Alternate Run Modes:Automated Calibration with Shuffled Complex Evolution
  ...by varying parameter values within a range specfied by the user in the SCE control file. The definition of the cost will play a large role in the final set o where calib_file.in is the name of the calibration control file.
  18 KB (2,856 words) - 14:57, 20 January 2016
• Tutorials:12 Groundwater
  <li>Click ''Yes'' to turn the interception option on in the job control</li> <li>Click ''Yes'' to turn the retention option on in the job control</li>
  16 KB (2,605 words) - 20:04, 6 August 2009
• GSSHA Software Primer
  :* [[Post-Processing:Output control|Output control]]
  6 KB (639 words) - 19:54, 7 October 2008

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)